Your television may not be able to function properly causing you to do check ups where the fault is. If it as an issue with power, it may exhibit characteristics such as shutting itself off or using a longer time frame to get reception as soon as you power it. This is not a very big challenge as it can be solved by TV power supply fixing. Here are the steps you ought to follow.
There are a number of tools you will need to effectively do the job. They include a capacitor, soldering iron, solder, screwdriver and a solder sucker. Confirm that your toolbox has all these items, and if not, you will have to go to the store. You should first determine if the problem is really what you want to repair. In television electric supplies, capacitors normally go bad causing them to leak and bulge hence the monitor will not get power.
After you have unplugged the television from the power source, place it with the monitor facing down on an area so that the screen is not damaged. Loosen all of the screws that you see on the back panel by use of a screwdriver. Once you have removed all of them, remove the back panel of your device and place it aside. You may have to wiggle it as there are no bolts securing it.
The next step is to locate where the circuit board is by following the board that the power cord is linked to. Disconnect the screws and connectors by using a screwdriver from the board. Ensure you note where they all came from as you will have to reattach them as they were. It is imperative you take pictures so that you do not get confused during reattaching. After the connectors and screws are unattached, remove the circuit board.
Find the malfunctioning capacitors. They are shaped like small cylinders and are different in height and width. Probably all of them appear normal. Search for those that have a brown to yellow fluid at the top or seem to have swollen at the surface. Such an appearance indicates that they have been overheated hence causing the problem. While you are getting rid of them, make sure that the copper pads are not destroyed.
Once you remove the faulty ones, use the new ones to replace them. Take note of the positive polarity and negative polarity when substituting them. You should then indicate the negative leads that are on the board using the soldering iron. The negative section is characterized by a grey stripe. Since the capacitors are polarity sensitive, make sure they are installed well.
Once you have done the replacement, the device should be reassembled, and then the power checked. After the connectors have been interchanged and the bolts and back panel reattached, determine if the fault has been rectified. A power surge will definitely cause the fuse to blow. If you notice that the problem has not been fixed, consider checking its fuse. Ensure that you replace it with an appropriate one.
If none of these solves the problem, your last option is to replace the main circuit board of the device. This is because if it is damaged, the television would not work correctly. Before doing this, you should have guidance on how it should be replaced so that you do not cause further damage to the device.
There are a number of tools you will need to effectively do the job. They include a capacitor, soldering iron, solder, screwdriver and a solder sucker. Confirm that your toolbox has all these items, and if not, you will have to go to the store. You should first determine if the problem is really what you want to repair. In television electric supplies, capacitors normally go bad causing them to leak and bulge hence the monitor will not get power.
After you have unplugged the television from the power source, place it with the monitor facing down on an area so that the screen is not damaged. Loosen all of the screws that you see on the back panel by use of a screwdriver. Once you have removed all of them, remove the back panel of your device and place it aside. You may have to wiggle it as there are no bolts securing it.
The next step is to locate where the circuit board is by following the board that the power cord is linked to. Disconnect the screws and connectors by using a screwdriver from the board. Ensure you note where they all came from as you will have to reattach them as they were. It is imperative you take pictures so that you do not get confused during reattaching. After the connectors and screws are unattached, remove the circuit board.
Find the malfunctioning capacitors. They are shaped like small cylinders and are different in height and width. Probably all of them appear normal. Search for those that have a brown to yellow fluid at the top or seem to have swollen at the surface. Such an appearance indicates that they have been overheated hence causing the problem. While you are getting rid of them, make sure that the copper pads are not destroyed.
Once you remove the faulty ones, use the new ones to replace them. Take note of the positive polarity and negative polarity when substituting them. You should then indicate the negative leads that are on the board using the soldering iron. The negative section is characterized by a grey stripe. Since the capacitors are polarity sensitive, make sure they are installed well.
Once you have done the replacement, the device should be reassembled, and then the power checked. After the connectors have been interchanged and the bolts and back panel reattached, determine if the fault has been rectified. A power surge will definitely cause the fuse to blow. If you notice that the problem has not been fixed, consider checking its fuse. Ensure that you replace it with an appropriate one.
If none of these solves the problem, your last option is to replace the main circuit board of the device. This is because if it is damaged, the television would not work correctly. Before doing this, you should have guidance on how it should be replaced so that you do not cause further damage to the device.
About the Author:
To help you get your TV power supply, simply go to our online page for details. You will find all the relevant information by clicking here http://www.tekbyus.com.
No comments:
Post a Comment